Performing switch startup and initial configuration

performing switch startup and initial configuration Junos for ex-series switches come with an ezsetup initial configuration wizard to help get your switch operational quickly ezsetup automates the initial configuration by presenting a series of basic initial configuration options such as the management ip address, root password, system time settings, and management vlan settings.

• erase the startup configuration and reload a router to the default state switch, switch to router, and host to router introduction to routing and packet. Basic switch configuration (21) switches are one of the most numerous devices installed onto the corporate network infrastructure configuring them can be fun and challenging. Performing the initial configuration to complete the initial configuration for the switch, follow these steps: step 1 at the terminal prompt, enter the enable command to enter privileged exec mode. If a switch is asking you to save current configuration in nvram, you should answer 'no' and proceed with the reload by hitting enter twice confirming the last question notice packet tracer does not greet you with: 'would you like to enter initial configuration dialog' which is the case on a real switch.

Qfx5200 you must perform the initial configuration of the qfx5200 through the console port using the cli or through zero touch provisioning (ztp) in order to use ztp to provision the device, you must have access to a dynamic host control protocol (dhcp) server, and a file transfer protocol (anonymous ftp), hypertext transfer protocol (http), or trivial file transfer protocol (tftp) server on. Verify and save the switch configuration using the copy running-config startup-config command to clear the switch configuration, use the erase startup-config command and then the reload command it may also be necessary to erase any vlan information using the command delete flash:vlandat. Lab 1-1: performing switch startup and initial configuration activity overview objectives in this activity, you will observe the switch boot procedure and perform basic switch configuration. Initial configuration configuration begins with naming each switch and assigning an ip address to a management interface on each switch shown in figure 7-2refer to chapter 5, using catalyst software, for examples of setting system and host names, along with setting an enable password.

View lab report - performing switch startup and initial configuration from cit 245 at university of phoenix 1 individual: performing switch startup and initial configuration cit/245 4/11/2016 jimmy. Complete the performing switch startup and initial configuration lab in toolwire® write a summary of the skills performed in the lab and what you learned write a review of cit 245 week 4 individual assignment performing switch startup and initial configuration.

To perform this initial configuration, you must access the switch with a console cable or a usb cable for console emulation you could also choose to configure tacacs+ authentication, but that involves more configuration work and a working tacacs+ server. In addition to being a quick and easy way to perform an initial configuration, the system configuration dialog also is useful for performing basic configuration changes after an initial configuration has been performed. As switch load this configuration back in ram in startup of device, at nvram it is known as startup-config show vlan for administrative purpose, switch automatically create vlan 1 and assign all its interfaces to it. Oolwire® lab resource: toolwire® complete the performing switch startup and initial configuration lab in toolwire® write a summary of the skills performed in the lab and what you learned.

Performing switch startup and initial configuration

Initial switch access chapter 2: initial configuration and recovery step 8 type write (or copy running-config startup-config) to save the new configuration to the startup-config file. Page 2 table of contents physical topology diagram lab 1-1: switch startup and initial configuration visual topology command list task 1: reload and check that the switch is set to factory defaults. Task 1: perform a reload and verify that the switch is unconfigured step 2: since the erase startup-config command is a privileged-level command, entering it in user exec mode will have no effect to the system.

Task 1 - performing switch startup and initial configuration step 1: power on nycore1 action: select nycore1 within the device list, then within the device tool bar located below the device window, click the power button. Performing switch startup and initial configuration vlab (20 points) write a paragraph (a minimum of five college-level sentences) below that summarizes what was accomplished in this lab, what you learned by performing it, how it relates to this week's tcos and other course material, and just as importantly, how you feel it will benefit you in your academic and professional career. Step 5: use the appropriate command to verify that the switch doesn't have a current startup-configuration and use the appropriate show command to display information about the device hardware and software parameters. Switch startup now that you have a basic understanding of the chassis of the 2960, you are ready to learn about the bootup process of the switch: this includes the running of hardware.

Lab 1-1: switch startup and initial configuration task 1: reload and check that the switch is set to factory defaults step 1: assign an ip address to your pc using the details listed in the visual topology diagram. 1-1 task performing switch startup and initial configuration - download as pdf file (pdf), text file (txt) or view presentation slides online scribd is the world's largest social reading and publishing site. Which procedure is used to access a cisco 2960 switch when performing an initial configuration in a secure environment use the console port to locally access the switch from a serial or usb interface of the pc.

performing switch startup and initial configuration Junos for ex-series switches come with an ezsetup initial configuration wizard to help get your switch operational quickly ezsetup automates the initial configuration by presenting a series of basic initial configuration options such as the management ip address, root password, system time settings, and management vlan settings. performing switch startup and initial configuration Junos for ex-series switches come with an ezsetup initial configuration wizard to help get your switch operational quickly ezsetup automates the initial configuration by presenting a series of basic initial configuration options such as the management ip address, root password, system time settings, and management vlan settings. performing switch startup and initial configuration Junos for ex-series switches come with an ezsetup initial configuration wizard to help get your switch operational quickly ezsetup automates the initial configuration by presenting a series of basic initial configuration options such as the management ip address, root password, system time settings, and management vlan settings.
Performing switch startup and initial configuration
Rated 4/5 based on 11 review

2018.